Difference between revisions of "Trackballs"
(→4.5" Atari Trackballs (Missile Command, Atari Football)) |
(→4.5" Atari Trackballs (Missile Command, Atari Football)) |
||
| Line 3: | Line 3: | ||
== 4.5" Atari Trackballs (Missile Command, Atari Football) == | == 4.5" Atari Trackballs (Missile Command, Atari Football) == | ||
| − | These giant trackballs are sometimes known as 4-inch, but are actually | + | [[Image:bigballs.jpg|left|thumb|4.5" trackballs (w/o optical boards)]]These giant trackballs are sometimes known as 4-inch, but are actually four and a half inches in diameter. They were some of the first trackballs put into use, and are made of machined aluminum; clearly designed to survive intense abuse. |
[[Vendors|Happ]] sells a 4.5" trackball. The ball itself is usable in an Atari 4.5" (a 4.5" diameter sphere is a 4.5" diameter sphere), but the mechanism itself is a different, less industrial design. | [[Vendors|Happ]] sells a 4.5" trackball. The ball itself is usable in an Atari 4.5" (a 4.5" diameter sphere is a 4.5" diameter sphere), but the mechanism itself is a different, less industrial design. | ||
| Line 10: | Line 10: | ||
The original optical boards on these are fairly easy to interface with an [[Optical_Encoders#Opti-PAC|Opti-PAC]] (and therefore most other [[Optical_Encoders|optical control interfaces]]). This is the pin-out for the 10-pin molex plug found on the optical boards: | The original optical boards on these are fairly easy to interface with an [[Optical_Encoders#Opti-PAC|Opti-PAC]] (and therefore most other [[Optical_Encoders|optical control interfaces]]). This is the pin-out for the 10-pin molex plug found on the optical boards: | ||
| − | [[Image: | + | [[Image:Atari_Steering.jpg|right]] |
{| | {| | ||
|1 | |1 | ||
| Line 47: | Line 47: | ||
On an Opti-PAC, the "A/HI" jumper should be set. | On an Opti-PAC, the "A/HI" jumper should be set. | ||
| − | There are a few [[Vendors|vendors]] that sell replacement bearings and roller-shafts for these | + | There are a few [[Vendors|vendors]] that sell replacement bearings and steel roller-shafts for these (they are often referred to as 4" trackball rollers). |
Revision as of 23:45, 2 March 2006
This page should contain brief descriptions of various trackballs available, and details of their setup. If any one portion of the page starts getting a little too long, a seperate page may be started for that topic.
4.5" Atari Trackballs (Missile Command, Atari Football)
These giant trackballs are sometimes known as 4-inch, but are actually four and a half inches in diameter. They were some of the first trackballs put into use, and are made of machined aluminum; clearly designed to survive intense abuse.
Happ sells a 4.5" trackball. The ball itself is usable in an Atari 4.5" (a 4.5" diameter sphere is a 4.5" diameter sphere), but the mechanism itself is a different, less industrial design.
Any 4.5" diameter ball, particularly a candle-pin and/or duck-pin bowling ball, is a swap-out replacement for the 25+ year old originals.
The original optical boards on these are fairly easy to interface with an Opti-PAC (and therefore most other optical control interfaces). This is the pin-out for the 10-pin molex plug found on the optical boards:
| 1 | no signal |
| 2 | no signal |
| 3 | no signal |
| 4 | Axis 1 |
| 5 | no signal |
| 6 | no signal |
| 7 | no signal |
| 8 | Axis 2 |
| 9 | +5v |
| 10 | ground |
There were a number of slightly different boards with this same pin-out.
On an Opti-PAC, the "A/HI" jumper should be set.
There are a few vendors that sell replacement bearings and steel roller-shafts for these (they are often referred to as 4" trackball rollers).
